From: owner-ammf-digest@smoe.org (alt.music.moxy-fruvous digest) To: ammf-digest@smoe.org Subject: alt.music.moxy-fruvous digest V14 #4310 Reply-To: ammf@fruvous.com Sender: owner-ammf-digest@smoe.org Errors-To: owner-ammf-digest@smoe.org Precedence: bulk alt.music.moxy-fruvous digest Thursday, June 11 2020 Volume 14 : Number 4310 Today's Subjects: ----------------- Finally, The Flash Drive Has Arrived To Save Valuable Files ["Flash Drive] Confirm this email please ["J. Lucas" <>] ---------------------------------------------------------------------- Date: Wed, 10 Jun 2020 07:39:33 -0400 From: "Flash Drive" <**FlashDrive**@lifedrive.today> Subject: Finally, The Flash Drive Has Arrived To Save Valuable Files Finally, The Flash Drive Has Arrived To Save Valuable Files http://lifedrive.today/R76-bBzDaJiVa7uiUoGAuq_KvzfDo215a7gtbyPDjrxm0h4 http://lifedrive.today/DxS9EG2GBXLZ0DKgnMKfnlKGpiNO3YjLn0qx6SNQvzFubyM the tip of a hot iron on the cloth that lies immediately above the dent, taking great care not to burn the wood. The transfer of heat from the iron to the wood will cause compressed fibres in the dent to recover their original dimensions. As a result the dent will diminish in size or even disappear completely, although removal of large dents may require a number of wetting and heating cycles. The wood in the recovered dent should then be dried and sanded smooth to match the surrounding wood. Gouges and holes in wood are more difficult to repair than dents because wood fibres have been cut, torn and removed from the wood. Larger gouges and splits are best repaired by patching the void with a piece of wood that matches the colour and grain orientation of the wood under repair. Patching wood requires skill, but when done properly it is possible to create a repair that is very difficult to see. An alternative to patching is filling (sometimes known as stopping). Numerous coloured fillers (putties and waxes) are produced commercially and are coloured to match different wood species. Successful filling of voids in wood requires the filler to precisely match the colour and grain pattern of the wood around the void, which is difficult to achieve in practice. Furthermore, filled voids do not behave like wood during subsequent finishing steps, and they age differently to wood. Hence, repairs to wood using fillers may noticeable. Therefore filling is best used with opaque finishes rather than semitransparent finishes, which allow the grain of the wood to be seen. Macro photo of 120 grit sandpaper Macro photo of 220 grit sandpaper Macro photo of 320 grit sandpaper Glue smears and droplets are sometimes present around the joints of furniture. They can be removed using a combination of scraping, scrubbing and sanding. These approaches remove surface glue, but not the glue beneath the wood surface. Sub-surface glue will reduce the absorption of stain by wood, and may alter the scratch pattern created by sanding. Both these effects will influence the way in which the wood colours when stains are used to finish the wood. To overcome this problem it may be necessary to locally stain and touch-up areas previously covered by glue to ensure that the finish on such areas matches that of the surrounding wood. Bleaching and removal of stains Wood surfaces are occasionally affected by various organic and inorganic stains. Sometimes such stains enhance the colour and appearance of wood. For example, oak wood affected by the beef-steak fungus has a deep rich, attractive, brown colour and there is no reason to remove the stain from the wood prior to finishing. The same applies to spalted wood whose attractive appearance is again caused by fungi. On the other hand some fungal stains and those caused by the reaction of iron with wood can disfigure wood. These stains can be removed from wood using bleach. Bleaches are also occasionally used to reduce the difference in colour between lighter sapwood and heartwood and also colour variation within heartwood. Such bleaching make it easier to achieve a uniformly coloured wood when the wood is subsequently coloured with pigmented stains and dyes (see below). Furthermore, the natural colours of wood fade when wood is exposed to sunlight, and more permanent colours can be created by bleaching wood to remove its natural colour and then re-colouring the wood using artificial, light-fast, stains. The bleaches used to remove unwanted fungal stains from wood include two-part peroxide bleach and solutions of sodium hypochlorite. The former is particularly effective at removing the natural colour of wood before it is recoloured with pigmented stains or dyes. Oxalic acid is particularly effective at removing iron stains from ------------------------------ Date: Wed, 10 Jun 2020 16:03:55 +0000 From: "J. Lucas" <> Subject: Confirm this email please I am yet to get your response on my investment offer to you on Blockchain network marketing opportunity. J. Lucas ------------------------------ End of alt.music.moxy-fruvous digest V14 #4310 **********************************************